← Back
Editing: imapsieve.txt
IMAPSIEVE plugins for Pigeonhole Relevant specifications ======================= doc/rfc/imapsieve.rfc6785.txt Introduction ============ As defined in the base specification, the Sieve language is used only during delivery. However, in principle, it can be used at any point in the processing of an email message. RFC 6785 defines the use of Sieve filtering in IMAP, operating when messages are created or their attributes are changed. This feature extends both Sieve and IMAP. Therefore, Pigeonhole provides both an IMAP and a Sieve plugin. The IMAP plugin is called "imap_sieve" and the Sieve plugin is called "sieve_imapsieve". The basic IMAPSIEVE capability allows attaching a Sieve script to a mailbox (or any mailbox) by setting a special IMAP METADATA entry. This way, users can configure Sieve scripts that are run for IMAP events in their mailboxes. The Pigeonhole implementation also adds the ability for administrators to configure Sieve scripts outside the user's control, that are run either before or after a user's script if there is one. Dovecot-specific Environment Items ================================== The "imapsieve" extension defined in RFC 6785 defines additional environment items for the "environment" extension defined in RFC 5183. Beyond those, Dovecot defines a few more. These are available when the Dovecot-specific "vnd.dovecot.imapsieve" extension is enabled using the "require" command. The "vnd.dovecot.imapsieve" extension implicitly uses the "imapsieve" extension, so that extension does not need to be enabled as well in that case. The following Dovecot-specific environment items are added: vnd.dovecot.mailbox-from The mailbox where the message is being copied or moved from (the source mailbox). This environment item is only set when the Sieve script is executed from an IMAP COPY or MOVE command. vnd.dovecot.mailbox-to The mailbox where the message is being copied to (the destination mailbox). If the Sieve script is not executed from an IMAP COPY or MOVE command, this environment is always equal to the "imap.mailbox" environment item. Otherwise, the "imap.mailbox" item points to the mailbox where the Sieve script is executing for, which may actually be the source mailbox (see the imapsieve_mailboxXXX_copy_source_after setting). Configuration ============= The IMAP plugin is activated by adding it to the mail_plugins setting for the imap protocol: protocol imap { mail_plugins = $mail_plugins imap_sieve } This only will enable support for administrator scripts. User scripts are only supported when additionally a Sieve URL is configured using the imapsieve_url plugin setting. This URL points to the ManageSieve server that users need to use to upload their Sieve scripts. This URL will be shown to the client in the IMAP CAPABILITY response as IMAPSIEVE=<URL>. The Sieve plugin is activated by adding it to the sieve_plugins setting: sieve_plugins = sieve_imapsieve This plugin registers the "imapsieve" extension with the Sieve interpreter. This extension is enabled implicitly, which means that it does not need to be added to the "sieve_extensions" setting. Note that the "imapsieve" extension can only be used from IMAP. When it is used in the active delivery script, it will cause runtime errors. To make a Sieve script suitable for both delivery and IMAP, the availability of the extension can be tested using the "ihave" test (RFC 5463) as usual. The following settings are recognized the "imap_sieve" plugin: imapsieve_url = If configured, this setting enables support for user Sieve scripts in IMAP. So, leave this unconfigured if you don't want users to have the ability to associate Sieve scripts with mailboxes. The value is an URL pointing to the ManageSieve server that users must use to upload their Sieve scripts. imapsieve_mailboxXXX_name = This setting configures the name of a mailbox for which administrator scripts are configured. The `XXX' in this setting is a sequence number, which allows configuring multiple associations between Sieve scripts and mailboxes. The settings defined hereafter with matching sequence numbers apply to the mailbox named by this setting. The sequence of configured mailboxes ends at the first missing "imapsieve_mailboxXXX_name" setting. This setting supports wildcards with a syntax compatible with the IMAP LIST command, meaning that this setting can apply to multiple or even all ("*") mailboxes. imapsieve_mailboxXXX_before = imapsieve_mailboxXXX_after = When an IMAP event of interest occurs, these sieve scripts are executed before and after any user script respectively. These settings each specify the location of a single sieve script. The semantics of these settings are very similar to the "sieve_before" and "sieve_after" settings: the specified scripts form a sequence together with the user script in which the next script is only executed when an (implicit) keep action is executed. imapsieve_mailboxXXX_causes = Only execute the administrator Sieve scripts for the mailbox configured with "imapsieve_mailboxXXX_name" when one of the listed IMAPSIEVE causes apply. This has no effect on the user script, which is always executed no matter the cause. imapsieve_mailboxXXX_from = Only execute the administrator Sieve scripts for the mailbox configured with "imapsieve_mailboxXXX_name" when the message originates from the indicated mailbox. This setting supports wildcards with a syntax compatible with the IMAP LIST command imapsieve_mailboxXXX_copy_source_after = When the cause is "COPY", run the specified Sieve script for the message in the source mailbox after the Sieve script for the corresponding message in the destination mailbox successfully finishes executing . This does not apply to moved messages, since the message is removed from the source mailbox in that case. imapsieve_expunge_discarded=no When enabled, discarded messages (for which no keep action is in effect) will be expunged immediately when the Sieve script execution is succcessful. Normally, such messages are only marked with the "\Deleted" flag and will be expunged only when the client explicitly issues an IMAP EXPUNGE command on the mailbox at a later time. Example ------- protocol imap { # Space separated list of plugins to load (default is global mail_plugins). mail_plugins = $mail_plugins imap_sieve } plugin { sieve_plugins = sieve_imapsieve imapsieve_url = sieve://sieve.example.org # From elsewhere to Spam folder imapsieve_mailbox1_name = Spam imapsieve_mailbox1_causes = COPY imapsieve_mailbox1_before = file:/usr/lib/dovecot/sieve/report-spam.sieve # From Spam folder to elsewhere imapsieve_mailbox2_name = * imapsieve_mailbox2_from = Spam imapsieve_mailbox2_causes = COPY imapsieve_mailbox2_before = file:/usr/lib/dovecot/sieve/report-ham.sieve }
Save File
Cancel