← Back
Editing: v2.1.0-ReleaseNotes
Cryptsetup 2.1.0 Release Notes ============================== Stable release with new features and bug fixes. Cryptsetup 2.1 version uses a new on-disk LUKS2 format as the default LUKS format and increases default LUKS2 header size. The legacy LUKS (referenced as LUKS1) will be fully supported forever as well as a traditional and fully backward compatible format. When upgrading a stable distribution, please use configure option --with-default-luks-format=LUKS1 to maintain backward compatibility. This release also switches to OpenSSL as a default cryptographic backend for LUKS header processing. Use --with-crypto_backend=gcrypt configure option if you need to preserve legacy libgcrypt backend. Please do not use LUKS2 without properly configured backup or in production systems that need to be compatible with older systems. Changes since version 2.0.6 ~~~~~~~~~~~~~~~~~~~~~~~~~~~ * The default for cryptsetup LUKS format action is now LUKS2. You can use LUKS1 with cryptsetup option --type luks1. * The default size of the LUKS2 header is increased to 16 MB. It includes metadata and the area used for binary keyslots; it means that LUKS header backup is now 16MB in size. Note, that used keyslot area is much smaller, but this increase of reserved space allows implementation of later extensions (like online reencryption). It is fully compatible with older cryptsetup 2.0.x versions. If you require to create LUKS2 header with the same size as in the 2.0.x version, use --offset 8192 option for luksFormat (units are in 512-bytes sectors; see notes below). * Cryptsetup now doubles LUKS default key size if XTS mode is used (XTS mode uses two internal keys). This does not apply if key size is explicitly specified on the command line and it does not apply for the plain mode. This fixes a confusion with AES and 256bit key in XTS mode where code used AES128 and not AES256 as often expected. Also, the default keyslot encryption algorithm (if cannot be derived from data encryption algorithm) is now available as configure options --with-luks2-keyslot-cipher and --with-luks2-keyslot-keybits. The default is aes-xts-plain64 with 2 * 256-bits key. * Default cryptographic backend used for LUKS header processing is now OpenSSL. For years, OpenSSL provided better performance for PBKDF. NOTE: Cryptsetup/libcryptsetup supports several cryptographic library backends. The fully supported are libgcrypt, OpenSSL and kernel crypto API. FIPS mode extensions are maintained only for libgcrypt and OpenSSL. Nettle and NSS are usable only for some subset of algorithms and cannot provide full backward compatibility. You can always switch to other backends by using a configure switch, for libgcrypt (compatibility for older distributions) use: --with-crypto_backend=gcrypt * The Python bindings are no longer supported and the code was removed from cryptsetup distribution. Please use the libblockdev project that already covers most of the libcryptsetup functionality including LUKS2. * Cryptsetup now allows using --offset option also for luksFormat. It means that the specified offset value is used for data offset. LUKS2 header areas are automatically adjusted according to this value. (Note units are in 512-byte sectors due to the previous definition of this option in plain mode.) This option can replace --align-payload with absolute alignment value. * Cryptsetup now supports new refresh action (that is the alias for "open --refresh"). It allows changes of parameters for an active device (like root device mapping), for example, it can enable or disable TRIM support on-the-fly. It is supported for LUKS1, LUKS2, plain and loop-AES devices. * Integritysetup now supports mode with detached data device through new --data-device option. Since kernel 4.18 there is a possibility to specify external data device for dm-integrity that stores all integrity tags. * Integritysetup now supports automatic integrity recalculation through new --integrity-recalculate option. Linux kernel since version 4.18 supports automatic background recalculation of integrity tags for dm-integrity. Other changes and fixes ~~~~~~~~~~~~~~~~~~~~~~~ * Fix for crypt_wipe call to allocate space if the header is backed by a file. This means that if you use detached header file, it will now have always the full size after luksFormat, even if only a few keyslots are used. * Fixes to offline cryptsetup-reencrypt to preserve LUKS2 keyslots area sizes after reencryption and fixes for some other issues when creating temporary reencryption headers. * Added some FIPS mode workarounds. We cannot (yet) use Argon2 in FIPS mode, libcryptsetup now fallbacks to use PBKDF2 in FIPS mode. * Rejects conversion to LUKS1 if PBKDF2 hash algorithms in keyslots differ. * The hash setting on command line now applies also to LUKS2 PBKDF2 digest. In previous versions, the LUKS2 key digest used PBKDF2-SHA256 (except for converted headers). * Allow LUKS2 keyslots area to increase if data offset allows it. Cryptsetup can fine-tune LUKS2 metadata area sizes through --luks2-metadata-size=BYTES and --luks2-keyslots-size=BYTES. Please DO NOT use these low-level options until you need it for some very specific additional feature. Also, the code now prints these LUKS2 header area sizes in dump command. * For LUKS2, keyslot can use different encryption that data with new options --keyslot-key-size=BITS and --keyslot-cipher=STRING in all commands that create new LUKS keyslot. Please DO NOT use these low-level options until you need it for some very specific additional feature. * Code now avoids data flush when reading device status through device-mapper. * The Nettle crypto backend and the userspace kernel crypto API backend were enhanced to allow more available hash functions (like SHA3 variants). * Upstream code now does not require libgcrypt-devel for autoconfigure, because OpenSSL is the default. The libgcrypt does not use standard pkgconfig detection and requires specific macro (part of libgcrypt development files) to be always present during autoconfigure. With other crypto backends, like OpenSSL, this makes no sense, so this part of autoconfigure is now optional. * Cryptsetup now understands new --debug-json option that allows an additional dump of some JSON information. These are no longer present in standard debug output because it could contain some specific LUKS header parameters. * The luksDump contains the hash algorithm used in Anti-Forensic function. * All debug messages are now sent through configured log callback functions, so an application can easily use own debug messages handling. In previous versions debug messages were printed directly to standard output.) Libcryptsetup API additions ~~~~~~~~~~~~~~~~~~~~~~~~~~~ These new calls are now exported, for details see libcryptsetup.h: * crypt_init_data_device * crypt_get_metadata_device_name functions to init devices with separate metadata and data device before a format function is called. * crypt_set_data_offset sets the data offset for LUKS to the specified value in 512-byte sectors. It should replace alignment calculation in LUKS param structures. * crypt_get_metadata_size * crypt_set_metadata_size allows one to set/get area sizes in LUKS header (according to specification). * crypt_get_default_type get default compiled-in LUKS type (version). * crypt_get_pbkdf_type_params allows one to get compiled-in PBKDF parameters. * crypt_keyslot_set_encryption * crypt_keyslot_get_encryption allows one to set/get per-keyslot encryption algorithm for LUKS2. * crypt_keyslot_get_pbkdf allows one to get PBKDF parameters per-keyslot. and these new defines: * CRYPT_LOG_DEBUG_JSON (message type for JSON debug) * CRYPT_DEBUG_JSON (log level for JSON debug) * CRYPT_ACTIVATE_RECALCULATE (dm-integrity recalculate flag) * CRYPT_ACTIVATE_REFRESH (new open with refresh flag) All existing API calls should remain backward compatible. Unfinished things & TODO for next releases ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ * Optional authenticated encryption is still an experimental feature and can have performance problems for high-speed devices and device with larger IO blocks (like RAID). * Authenticated encryption does not use encryption for a dm-integrity journal. While it does not influence data confidentiality or integrity protection, an attacker can get some more information from data journal or cause that system will corrupt sectors after journal replay. (That corruption will be detected though.) * The LUKS2 metadata area increase is mainly needed for the new online reencryption as the major feature for the next release.
Save File
Cancel